PO-80
recordfactory
user guide
ガイド
1.0

notice. read this first.


save all provided instructions for later use. follow all warnings and instructions marked on the product.
1. read instructions. all the safety and operating instructions should be read before the product is operated.2. retain instructions. the safety and operating instructions should be retained for future reference.3. heed warnings. all warnings on the product and in the operating instructions should be adhered to.4. follow instructions. all operating and use instructions should be followed.5. cleaning. unplug this product from its power source before cleaning. do not use liquid cleaners or aerosol cleaners. clean only with dry cloth.
warning
be sure to observe the following to avoid fire or electric shock.
if metal, water or foreign matter gets inside the product while product is operating, disconnect the usb cable from the main unit.
if smoke, unusual odor, unusual noise, drop or damage occurs, disconnect the usb cable from the main unit.do not use the usb terminal or power terminal if it is not completely inserted.
do not use the usb terminal or power terminal with dust attached, and do not bring any metal objects close to the terminal.

caution
for your own safety, please carefully read the instructions and precautions in this manual before experimenting.
there is a risk of suffocation, so beware of small parts such as screws, around children.
modifying or any use other than the intended use listed in this kit is strictly prohibited and is to be done at your own risk.
do not use if the main unit or the parts are damaged or deformed.
do not spill liquids on the unit, or operate the unit if it is wet.
operating power is 5V 1.0A. use the usb ac adapter for this operating power.
caution
after use, disconnect the usb cable from the main unit. do not move the unit while the cable is connected.use and keep the unit on a flat and stable surface.do not use or store the unit in places exposed to oil slicks or steam, or in places with high level of moisture or dust.when pulling the cord to connect / disconnect the usb terminal or power supply terminal, be sure to hold the connector firmly.do not insert or remove cables with wet hands.when cleaning, be sure to remove the usb cable from the main unit.keep out of reach of small children at all times.
what's in the box

Check that the following items are included when you open the box
assembly kit(multiple pieces)
spare cutting needle
X6
black 5-inch blank records (both sides can be used)
X6
cut & fold record sleeves
center label sticker sheet
gakken magazine
USB power cable
3.5 mm stereo trs to mono ts audio cable
adapter for 7-inch records
overview
rotation speed switch
33 → 33⅓ revolutions per minute 45 → 45 revolutions per minute (rpm)
recording / playback switch
recording ○ playback  ▷
LED

the LED lights up when the power is on
volume switch
power on / off andsound input / output volume change
line in
connect the sound source or music device that you want to record from to this dedicated 3.5 mm line input mono audio socket
line out
here you can connect an external speaker or a pair of headphones. this will cancel out the internal speaker.
power terminal
dedicated USB power terminal for the USB power cable.
overview
rotation speed switch
33 → 33⅓ revolutions per minute45 → 45 revolutions per minute (rpm)

recording / playback switchrecording ○ 
playback ▷

volume switchpower on / off andsound input / output volume change

LEDthe LED lights up when the power is on
line inconnect the sound source or music device that you want to record from to this dedicated 3.5 mm line input mono audio socket
line outhere you can connect an external speaker or a pair of headphones. this will cancel out the internal speaker.
power terminaldedicated USB power terminal for the USB power cable
cutter head
cutter head
cutting needle
tonearm
record needle
slide
built-in speaker
turntable
build
please read the included instructions and carefully follow the build guide to assemble your PO-80 record factory.
to prepare you will need a screwdriver, a cutter, a ruler and some glue. 
to power your unit use a usb power supply or a battery pack.
the estimated building time is about 60 minutes.good luck!
record
line in
connect your audio source to the line input.
adjust the needle pressure and slide the cutting arm to the end.
place and fasten a clean record on the turntable.
set the recording switch to recording. turn on and adjust volume with the volume dial. 
play the audio source at maximum volume and adjust the volume on PO-80 as needed. the cutter head should be stable and the sound should be clear.
push the cutting arm slightly forward to connect it with the pulley gear.
pause and reset your audio source. carefully lower the cutter head and set the cutting needle to the record.
play the audio source to record to the record. carefully remove any debris while cutting. raise the cutter head when finished.
record
line in
connect your audio source to the line input.
adjust the needle pressure and slide the cutting arm to the end.
place and fasten a clean record on the turntable.
set the recording switch to recording. turn on and adjust volume with the volume dial. 
play the audio source at maximum volume and adjust the volume on PO-80 as needed. the cutter head should be stable and the sound should be clear.
push the cutting arm slightly forward to connect it with the pulley gear.
pause and reset your audio source. carefully lower the cutter head and set the cutting needle to the record.
play the audio source to record to the record. carefully remove any debris while cutting. raise the cutter head when finished.
play
set the recording switch to playback.
place a record on the turntable.
lift the tonearm and place the needle in the groove of the record.
turn on and adjust volume with the volume dial.
line out
to use headphones or external speakers connect these into the output jack.
when playback is finished return the tonearm and turn off the power.
use the provided adapter to to play commercial 7 inch records.
play
set the recording switch to playback.
place a record on the turntable.
lift the tonearm and place the needle in the groove of the record.
turn on and adjust volume with the volume dial.
line out
to use headphones or external speakers connect these into the output jack.
when playback is finished return the tonearm and turn off the power.
use the provided adapter to to play commercial 7 inch records.
improve your recordings
to prepare your music for recording it's recommended to use an equalizer. record your music to a computer and use a low cut eq to achieve the best quality recordings. 
to help you out go to our mastering machine and upload your music.
you can use mp3 or wav files up to 4 minutes long.
after the file has been uploaded, pick your desired musical flavor and thendownload the mastered track. use this file when recording on your PO-80.
to further improve your recordings you can try to adjust the needle weight. experiment to find the optimal setting for your unit.
also adjust the input volume to steady the needle for recording. heavy vibration of the needle can cause skipping.
good luck and have fun experimenting!
accessories
bag
canvas bag to fit either the PO-80 record factory or 5'' or 7-inch records. 
view in shop
records 10-pack
a set of 10 blank 5-inch disks for your recordings.
view in shop
cutting head
a spare cutting head. it is recommenced to regularly replace the cutting head after some use for best sound quality.
view in shop
technicalspecs

record cutting & playback: monaural
assembly time:approx. 60 minutes 
recording time:33⅓ rpm approx. 4 minutes 45 rpm approx. 3 minutes (per side) 
motor: belt drive
power: USB 
input/output:3.5 mm mono ts jacks built-in speaker
dimensions:3.54" x 6.30" x 5.91"19 cm × 16 cm × 15 cm
weight:1.26 lb / 570 g